Data Center Gas Turbine Heat Rate at Part Load | USP&E

Data Center Generators

Gas Turbine Heat Rate and Part-Load Efficiency for Data Center Power

Fuel is the largest running cost of any gas turbine plant, and on a data center campus that runs its turbines around the clock it soon outweighs most other line items. The number that describes how well a turbine turns fuel into electricity is its heat rate, and the number on the data sheet is rarely the one a campus will see in service.

This guide explains heat rate in plain terms, shows how it changes at part load and on hot days, and sets out the dispatch and design choices that keep a data center’s turbines close to their best efficiency.

Heat rate in one paragraph

Heat rate is the fuel energy needed to produce one unit of electricity, usually given in kJ per kWh or Btu per kWh. Lower is better. Because one kWh equals 3,600 kJ, efficiency is simply 3,600 divided by the heat rate in kJ per kWh. A turbine with a heat rate of 9,000 kJ per kWh is 40 percent efficient; at 10,000 kJ per kWh it is 36 percent.

Check whether a figure is quoted on the lower or higher heating value of the fuel. Turbine data sheets normally use the lower heating value, while gas is often bought on the higher value, which makes the real fuel bill around 10 percent higher than a naive calculation suggests.

ISO ratings versus site conditions

Published heat rates are at ISO conditions: 15 degrees Celsius, sea level and 60 percent relative humidity, with set inlet and exhaust losses. A real site is rarely at those conditions. Higher ambient temperature reduces air density, cutting output and raising heat rate. Altitude has a similar effect on output.

For campuses in hot climates, the summer afternoon is the design point that matters. Our page on hot-day derate for campus turbines covers the output side; heat rate follows the same pattern and should be modelled for each month of the year.

Why part load costs fuel

Gas turbines are most efficient near full load. As load is reduced, firing temperature falls and the compressor still moves a large air flow, so more fuel is used per kWh. As a rough guide, heat rate at half load can be 15 to 30 percent worse than at full load, depending on the machine, with the penalty growing steeply below that.

A simple example shows the effect. A 30 MW unit at full load with a heat rate of 9,500 kJ per kWh burns about 285 GJ an hour. The same unit at 15 MW with a heat rate 25 percent higher burns about 178 GJ an hour, so half the output needs well over half the fuel.

Data center load is high and flat, mostly

Data center demand is steadier than most industrial loads, which suits turbines. But early in a campus’s life the IT load may be a fraction of the installed capacity, and AI training clusters can swing quickly between high and low draw. Both push turbines into part load.

Our page on AI power swings on campus turbines explains the transient side. For fuel, the question is how many hours per year each unit spends at which load, which comes from the IT ramp plan and the cooling load profile.

Unit count and dispatch strategy

Running fewer units at higher load is almost always more efficient than spreading the load across many units at low output. A plant built from several modular blocks can start and stop units as load changes, keeping the running units near their best heat rate.

The reserve policy has a fuel cost. Holding a spare unit running at low load for instant cover burns fuel all year; holding it on fast standby, backed by batteries or other ride-through, uses far less. Our guide to N+1 design for campus turbines discusses the reliability side of that trade.

Degradation and recovery

Heat rate worsens over time as compressor blades foul and hot section clearances open. Fouling is partly recoverable by online and offline compressor washing, and good inlet filtration slows it down. Clearance and coating wear are only recovered at hot section and major inspections.

Track corrected heat rate monthly against the acceptance test baseline. A steady drift calls for washing; a step change points to a fault worth investigating.

From heat rate to gas volume

Heat rate also sizes the fuel gas supply. Using the example above, 285 GJ an hour divided by a gas energy content of about 38 MJ per cubic metre gives roughly 7,500 cubic metres an hour for one unit at full load. Multiply by the number of units, add a margin for start-up and degradation, and the result sets the pipeline capacity and metering skid size.

This calculation should be repeated for the hottest and coldest site conditions, because both output and heat rate move with ambient temperature.

When exhaust heat is put to work

In simple cycle, roughly 60 percent of the fuel energy leaves through the stack. Some campuses recover part of it, for example to drive absorption chillers that carry cooling load, which lowers the electrical demand the turbines must meet. Heat rate on the electrical side stays the same, but the fuel used per unit of IT load falls.

Heat recovery adds equipment, back pressure and maintenance, so it is worth modelling only once the base dispatch case is clear.

What to ask vendors and put in the contract

Ask each turbine supplier for heat rate curves at 100, 75, 50 and 25 percent load across the site’s ambient range, on a clearly stated heating value basis, with stated inlet and exhaust losses. Compare machines on the expected load profile, not only at the ISO point.

Then fix guaranteed values and test methods in the contract, as described in our guide to performance guarantees for data center turbines. The broader engine versus turbine comparison is set out in our article on choosing between turbines and reciprocating engines.

About the authors

This guide comes from the USP&E performance engineers and plant operators who model, test and run gas turbine plants for industrial and data center clients. USP&E is an EPC and O&M contractor, not a broker, with 150+ power projects in 45+ countries, 25,000 MW contracted since 2002 and 24+ years in the field. Our data center power services run from feasibility through long-term operation.

Offices: Colorado Springs (1755 Telstar Dr, Suite 300), Knoxville (800 S Gay St, Suite 700), London (162-168 Regent Street), Johannesburg (22 Kildoon Rd, Bryanston), Cape Town (31 Brickfield Road, Woodstock) and China (No. 1 Ningzhou Road, Wuxi). Regions: USA | AFRICA | UK | UAE | CHINA. ISO 9001 and ISO 45001 certified.

Heat rate questions

What is gas turbine heat rate?

It is the fuel energy needed to make one kWh of electricity, usually in kJ per kWh. Lower heat rate means higher efficiency.

How do I convert heat rate to efficiency?

Divide 3,600 by the heat rate in kJ per kWh. A heat rate of 9,000 kJ per kWh equals 40 percent efficiency.

How much worse is heat rate at part load?

As a rough guide, heat rate at half load can be 15 to 30 percent worse than at full load, depending on the turbine.

Does hot weather affect gas turbine efficiency?

Yes. Higher ambient temperature reduces output and raises heat rate, so summer conditions should be the design case.

How can a data center keep its turbines efficient?

Run fewer units at higher load, use modular blocks that start and stop with demand, keep compressors clean and track corrected heat rate monthly.

Model fuel use for your campus

Send us your IT ramp plan, site climate and reserve policy, and our engineers will help you estimate turbine fuel use across the year.

If a document set is easier than a conversation, send it to info@uspeglobal.com or upload a summary through the campus power enquiry form; to talk it over, dial +27 10 822 2324. Units available now are listed in our natural gas turbine stock.


Where we operate

USA | AFRICA | UK | UAE | CHINA

USP&E United States

Colorado Springs Office: 1755 Telstar Dr, Suite 300

Knoxville Office: 800 S Gay St, Suite 700

USP&E South Africa

Johannesburg Office: 22 Kildoon Rd, Bryanston

Cape Town Office: 31 Brickfield Road, Woodstock

USP&E United Kingdom

London Office: 162-168 Regent Street

USP&E China

China Office: No. 1, Ningzhou Road, Wuxi

Call:+27 10 822 2324  |  E:info@uspeglobal.com

ISO Certifications
ISO9001ISO45001

Powering Possibility. Built for the Frontier.
Full-service EPC & O&M. Not a broker.

© 2026 USP&E · Data Center Generators is part of USP&E